GQF-C40橋梁伸縮縫施工技術

時間：2017-10-15作者：河北瑞博橡塑制品有限公司瀏覽：91

單組式伸縮縫主要材料：鋼質邊梁：采用16Mn的鋼軋制，部面呈c形。橡膠密封條：采用氯丁橡膠制造，具有良好的耐老化、耐撓性能。
A single group type expansion joint material: steel edge beam with steel rolling 16Mn, the Ministry is C. Rubber sealing strip: made of chloroprene rubber, it has good aging resistance and torsion resistance.
固錨件：有錨栓、錨環、錨板結構三種，設計工程師可根據橋面板設計厚度選用，間距一般為20cm，本廠也可根據設計工程師特定設計制造。
Solid anchor: there are anchor bolt, anchor ring, anchor plate structure of three kinds, the design engineer can be selected according to the thickness of the bridge deck design, spacing is generally 20cm, the factory can also be designed and manufactured according to the specific design engineer.
選定伸縮縫規格尺寸選定伸縮縫的規格尺寸與使用壽命關系很大，在設計時應考慮足夠的伸縮富余量。當橋梁位移方向與伸縮縫中心線正交時，選用伸縮縫規格比較*，但橋梁位移方向與伸縮縫中心斜交時，須分解成平行與垂直于中心線的兩個矢量，選用伸縮縫規格取決于兩個矢量當中的一個。與接縫平行的矢量：△Lp=△L.cosβ；與接縫垂直的矢量：△Lr=△Lr.sinβ式中：表示橋梁位移的總變形量；為位移方向與接縫方向的交角β=45゜∽135°△Lr是選用伸縮縫規格的依據，△Lp的變形一般由橡膠密封條的水平錯動老完成，對伸縮縫的選用無太大的影響。
It is very important to choose the expansion joint size and service life of the expansion joint specification size, and should consider enough expansion allowance in the design. When the bridge displacement direction and the center line of the orthogonal expansion joints, expansion joints selection specification is relatively easy, but the direction and displacement of bridge expansion joint center oblique, must be decomposed into parallel and perpendicular to the center line of the two vectors, the expansion joint specification depends on two vector one. With the vector parallel seam: Delta Lp= and delta L.cos beta; vector joint vertical: Delta Lr= Delta Lr.sin beta type: said the total deformation of bridge displacement; displacement direction and direction of the joint angle beta =45 to 135 DEG Lr Eve joy is the selection of expansion joint specification, the deformation is generally composed of delta Lp rubber sealing strip moving old wrong level, without too much influence on the expansion joint.
例：設計橋梁沿結構中心線位移95mm，伸縮縫與其斜交40°，按公式計算△Lr=73mm,△Lp=61mm選用本型號的伸縮縫是適用的。同時要注意，膠條以中部為準，較大水平錯動量在前后兩個方向都是不應**過40mm，如計算中發現有過量錯動，須選用較大規格的伸縮縫。設計時，如帶有人行道，防撞墻結構的，必須將設計角度，尺寸數據提供給本廠，便于工廠按設計要求整體制造。
Example: the design of bridge structure displacement along the center line of the 95mm, with its 40 degree oblique joints, calculated according to the formula of delta Lr=73mm, Delta Lp=61mm used this type of telescopic seam is applicable. At the same time, we should pay attention to the central part of the rubber strip, and the maximum horizontal dislocation should not exceed 40mm in the two directions. If the excessive movement is found in the calculation, the larger size expansion joint must be used. Design, such as with sidewalks, anti-collision wall structure, must design angle, size data provided to our factory, convenient for the factory according to the design requirements of the overall manufacturing.
單組式橋梁伸縮縫安裝前現場準備
Site preparation before single bridge expansion joint installation
GQF-C型伸縮縫是在本廠制造并組裝，若整條伸縮縫**長不能運輸或工程需分段施工，需在現場焊接一體后，再組裝橡膠密封條。
GQF-C type expansion joint is manufactured and assembled in our factory. If the whole expansion joint is too long to be transported or the project needs to be segmented, the rubber sealing strip should be assembled after welding on the spot.
（1）伸縮縫預留槽口、在澆筑擬安裝伸縮縫的梁體、橋臺時，在端部預留符合安裝尺寸的槽口、推薦尺寸見表1。表1單位mm固錨件型式槽口寬度（b）槽口深度（h）錨栓≥35080∽120錨環≥35080∽120錨板≥350≥150注：特殊設計另定
(1) the reserved slot of expansion joint and the beam and abutment in which the expansion joint should be installed, the notch fitting the installation dimension is reserved at the end, and the recommended size is shown in table 1. Table 1 mm solid anchor type slot width (b) depth of groove (H) anchor is greater than or equal to 35080 to 120 to 120 more than 35080 anchor ring anchor plate is greater than or equal to 350 = 150 note: special design on the other
（2）預埋鋼筋設置：在澆筑梁體或橋臺時，應設置預埋鋼筋。預埋深度不小于50cm，并與梁體、橋臺內結構鋼筋連接一體；間距尺寸為20cm應和伸縮縫錨固件保持一致。
(2) embedded steel bar setting: when pouring the beam or abutment, the embedded steel bar should be set. The embedment depth is not less than 50cm, and is connected with the beam body and the inner structure reinforcement of the abutment, and the spacing size is 20cm, which should be consistent with the expansion joint anchor.
（3）梁端間隙應不小于梁體伸長度，在預制、現澆或吊裝時由設計工程師根據當?shù)貧鉁卮_定。
(3) the beam end clearance should be not less than Tishen beam length in prefabricated and cast-in-situ or lifted according to the local temperature determined by the design engineer.
（4）調節伸縮縫定位尺寸“J”，根據安裝時氣溫計算正確，調節后，瑣緊定位壓板。
(4) adjust the expansion joint positioning size "J", according to the installation temperature calculation is correct, after adjustment, the locking positioning plate.
（5）用發泡塑料板嵌入梁端間隙內，其上部與伸縮縫鋼梁內側密合，盡量達到密封，防止?jié)仓炷習r出現漏漿、空洞。
(5) the foam plastic plate is embedded into the end clearance of the beam, and the upper part is close to the inner side of the expansion joint steel beam, so as to achieve the sealing as far as possible, and prevent the leakage of grout and cavity when pouring the concrete.
單組式橋梁伸縮縫安裝
Installation of single group expansion joint of bridge
（1）伸縮縫吊裝就位，檢查其中線線與梁縫中心線是否重合，其**面與路面標高是否一致，及時進行調整。
(1) joint hoisting, check for the line and the gap of the beam center line is coincident, the top surface and the pavement elevation is consistent, timely adjustment.
（2）將預娩鋼筋和伸縮縫錨固件焊接牢固，再橫穿12或16水平鋼筋。
(2) the pre delivery of rebar and anchor joints welded firmly, then across the 12 or 16 horizontal bars.
（3）立即拆除伸縮縫定位壓板，鏨去定位螺絲，并用角向砂輪磨去焊疤，補上油漆。
(3) the immediate removal of the expansion joint positioning plate, chisel to the positioning screw, and the angle to the wheel abrasion welding scar, fill the paint.
（4）用膠粘紙帶或木板密封伸縮縫**面縫口，在槽口部位即澆筑50號混凝土；用插入式振動棒，充分振搗密實。
(4) sealing the expansion joint top surface with adhesive tape or wood board; pouring concrete No. 50 at the notch; using the inserted vibrating bar to vibrate sufficiently.
（5）抹平混凝土過度段表面。用直尺檢查伸縮縫**面、過度段，應盡量與路面平順。做好混凝土養生后方可通車。
(5) the surface of the over section of the concrete is smoothed. Check the top and the over section of the expansion joint with the ruler, and try to be smooth with the road surface. Good concrete health can be opened to traffic.
（6）帶有防撞墻，人行道結構的伸縮縫，參造上述安裝工序作業。
(6) the expansion joint with the anti-collision wall and the sidewalk structure can be used for the above installation operation.


河北瑞博橡塑制品有限公司專注于橡膠止水帶,橡膠支座,密封膠等

• 詞條

  詞條說明

• GQF-C40橋梁伸縮縫施工技術

  單組式伸縮縫主要材料：鋼質邊梁：采用16Mn的鋼軋制，部面呈c形。橡膠密封條：采用氯丁橡膠制造，具有良好的耐老化、耐撓性能。 A single group type expansion joint material: steel edge beam with steel rolling 16Mn, the Ministry is C. Rubber sealing strip: made of c

• 橡膠止水帶的施工方法

  橡膠止水帶施工與安裝方法的正確性是使用橡膠止水帶的關鍵所在，我們知道橡膠止水帶是在混凝土澆注過程中部分或全部澆埋在混凝土中。由于混凝土中有許多尖角的石子和銳利的鋼筋，所以在止水帶定位和混凝土澆搗過程中，應注意安裝定位方法和澆搗壓力，以避免止水帶被刺破。由于塑料和橡膠的抗斷撕裂強度比拉伸強度低3-5倍，所以如果產品被刺破將會大幅度降低產品抵抗外力的能力，故在施工中要格外注意。?進行橡膠止水帶施工時具