Setting the clock system

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：112

Setting the clock system



The SIMATIC Drive Controller supports isochronous mode for the following clock systems:

PROFINET IO interface X150

PROFIBUS DP interface X126

Technology I/Os X142

With PROFIdrive Integrated

You can operate the clock systems separately or coupled on an isochronous basis. Exception: Isochronous coupling of the PROFIBUS DP interface is not possible. You can find information on the combinations in which you can couple the clock systems in Overview of isochronous mode.

You make the required settings in the relevant clock systems.

Once you have set and, if necessary, coupled the clock systems, you need to couple the OB servo with the clock system in which you wish to operate the drives / that is the leading clock system.

SINAMICS Integrated clock system

Proceed as follows to set the clock system of the SINAMICS Integrated:

Switch to the network view.

Click on PROFIdrive Integrated in the network view.

Make the settings for the SINAMICS Integrated under "Constant bus cycle time".
The SINAMICS Integrated is always isochronous (option is always selected).


圖片: SINAMICS Integrated (PROFIdrive Integrated) clock system

Adjust other settings if required – for example times Ti/To for reading in/outputting data in isochronous mode.

列表: Setting options for "Cycle time" in the SINAMICS Integrated clock system

Setting options	Note
Manual	With these settings, you operate the SINAMICS Integrated as an independent clock system.
Automatic minimum
Use local send clock [X142]	With this setting, you operate the SINAMICS Integrated in isochronous mode coupled with the clock system of the X142 technology I/Os. Use this setting if you want to use the technology I/Os isochronously with the OB servo, for example, for measuring input or output cam applications. Please note the following: You cannot operate the X142 technology I/Os in isochronous mode separately from SINAMICS Integrated. If you want to operate X142 technology I/Os and SINAMICS Integrated in isochronous mode simultaneously, always set coupled isochronous mode. Consistency checks ensure that the setting is correct.
Send clock of the PROFINET interface [X150]	With this setting, you operate SINAMICS Integrated in isochronous mode coupled with PROFINET interface X150. SINAMICS Integrated uses the system clock of PROFINET interface X150. Use this setting if you need to operate the SIMATIC Drive Controller in isochronous mode at PROFINET IO interface X150, for example, for the connection of drives or for synchronous operation across PLC.

X142 technology I/Os clock system

Proceed as follows to set the clock system of the X142 technology I/Os:

In the device view of STEP 7, select the CPU of the SIMATIC Drive Controller.

Navigate to "Advanced configuration" > "Isochronous mode" in the properties of the CPU.

Select the required settings from the "Source of send clock" drop-down list in the "Isochronous mode for local modules" section.


圖片: Technology I/O clock system

列表: Setting options for "Source of send clock" in the clock system of the technology I/Os

Setting options	Note
Local send clock	With this setting, you operate the X142 technology I/Os as an independent clock system, or as the leading clock system if you couple the clock system of the SINAMICS Integrated.
Using the send clock of the PROFINET interface [X150]	With this setting, you operate X142 technology I/Os in isochronous mode coupled with PROFINET interface X150. The X142 technology I/Os use the system clock of PROFINET interface X150.

PROFINET IO interface X150 clock system

Proceed as follows to set the clock system of PROFINET interface X150:

Select the PROFINET IO system in the network view of STEP 7.

Make the settings for the send clock, etc. under "PROFINET subnet" > "Domain management" > "Sync domains".

In coupled isochronous mode with other clock systems, the clock system of the PROFINET interface is always leading.

You can find additional information on configuring isochronous mode on PROFINET IO in the Isochronous mode function manual.

PROFIBUS interface X126 clock system

You must follow the rules below during configuration if you want to operate the PROFIBUS DP interface in isochronous mode:

列表: Rules for configuring isochronous mode for PROFIBUS DP interface

If ...	The configured cycle time of the PROFIBUS DP interface must...
A SINAMICS Integrated is configured	Be equal to or an integer multiple of the configured cycle time of the SINAMICS Integrated (PROFIdrive Integrated)
The X142 technology I/Os are operated in isochronous mode	Be equal to or an integer multiple of the configured cycle time of the X142 technology I/Os
The clock system of the PROFINET IO interface is coupled with one of the two clock systems.	Be equal to or an integer multiple of the configured cycle time of the PROFINET IO interface

Consistency checks ensure that the setting is correct.

Proceed as follows to set the clock system of the PROFIBUS interface:

Select the DP master system in the network view of STEP 7.

Make the settings for the DP cycle under "Constant bus cycle time".

提示 Isochronous coupling of the PROFIBUS interface with other clock systems is not possible. If you want to expand the drive configuration limits with distributed drive systems, connect those distributed drive systems over the PROFINET IO interface X150. Only the PROFINET IO interface X150 can be connected isochronously alongside the MC Servo to the clock system of SINAMICS Integrated and the X142 technology I/Os.




Synchronizing MC Servo with clock system

Proceed as follows to synchronize the MC Servo with a clock system:

Open the "Program blocks" folder in the project tree.

Select the "MC Servo" organization block.

Select the "Properties" command in the shortcut menu.

Select the "Cycle time" entry in the area navigation.

The option "Synchronous to the bus" must be selected in the dialog box.

In the "Source of send clock" drop-down list, select the clock system to be synchronized with the OB MC?Servo.


圖片: Synchronizing MC Servo with clock system

列表: Setting options for synchronization with a clock system

Setting options1)	Note
PROFIdrive system (1)	With this setting, you synchronize MC Servo with the clock system of SINAMICS Integrated.
PROFINET IO system (100)	With this setting, you synchronize MC Servo with PROFINET interface X150.
PLC_1 (0)	With this setting, you synchronize MC Servo with the clock system of technology I/Os X142.
DP master system (2)	With this setting, you synchronize MC Servo with PROFIBUS interface X126.

1) The designations may vary depending on the names assigned.




For coupled isochronous mode, you must always select the leading clock system.

Setting the application cycle

The application cycle of MC Servo is derived from the send clock and a configurable factor. The adjustable factors depend on the coupled clock system.


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• ListGenerator1500/300/400 FC

  ListGenerator1500/300/400 FCListGenerator FC 具有三個版本，其符號名稱如下：對于 S7-300ListGenerator300對于 S7-400ListGenerator400對于 S7-1500ListGenerator1500功能如果數據所包含的目標地址不完整，或者根本不包含目標地址，則在接收這樣的數據的 CPU 中，需要 FC ListGenera

• 軟件握手/硬件握手

  軟件握手/硬件握手簡介用于控制兩個通信伙伴之間數據流的握手協議。 使用握手程序可以防止兩個設備以不同的傳輸率操作時在傳輸期間產生數據丟失。握手程序握手有兩種基本類型：軟件握手（例如 XON/XOFF）硬件握手（例如 RTS/CTS）在通信模塊上按照以下方式執行數據流控制：一旦模塊通過組態切換到使用流控制的工作模式，模塊便會發送 XON 字符或?qū)?RTS 線路設置為 ON。如果在接收緩沖區溢出（接收

• 與S7-1200之間TCP通信二

  S7-200 SMART 與 S7-1200 之間 TCP 通信— S7-200 SMART 作為客戶端TCP 協議通信TCP 通信為面向連接的通信，需要雙方都調用指令以建立連接及交換數據。S7-200 SMART 與 S7-1200 通過 TCP 通信，在 S7-1200 調用 T-block 指令 ( TCON, TDISCON, TSEND, TRCV ) ，在 S7-200 SMART 調

• * 2 層功能 ST 常規

  ST 常規說明該頁面包含以下框：網橋**級 (Bridge Priority)?/?根**級 (Root Priority)（僅在線時可用）由網橋**級決定哪個設備成為根網橋。**級較高的網橋（換句話說，此參數的值較小）將成為根網橋。如果網絡中有多個設備具有相同**級，則 MAC 地址數值較小的設備將成為根網橋。網橋**級和 MAC 地址這兩個參數一起構成網橋標識符。由于根網橋