MC-LookAhead OB

時間：2021-07-27作者：上海騰希電氣技術有限公司瀏覽：98

MC-LookAhead OB



Description

When you create a kinematics technology object as of V5.0 for S7-1500T Motion Control, the organization block MC?LookAhead [OB97] is created automatically.

The movement preparation of the kinematics technology object is calculated in the MC?LookAhead [OB97] organization block.

The MC?LookAhead [OB97] is write-protected. The contents cannot be changed.

提示 Only one MC?LookAhead [OB97] per CPU The movements of all kinematics of a CPU are prepared in an MC?LookAhead [OB97] organization block. The MC?LookAhead [OB97] can only be created once.




All jobs of the job sequence are prepared in advance within the MC?LookAhead [OB97]. In this way, less time is required for movement preparation in the MC?Interpolator [OB92] organization block and you can set a shorter application cycle of the MC?Servo [OB91] organization block.

Block call and priority

The MC?LookAhead [OB97] is not called cyclically according to the configured priority in the execution system of the CPU.

You configure the priority of the MC?LookAhead [OB97] in the properties of the organization block under "General > Attributes > Priority". You can set values from 14 to 16 (default setting 15) for the priority. The priority of MC?LookAhead [OB97] must be lower than the priority of MC?Interpolator [OB92].

Cycle load

You can configure the maximum cycle load for the MC?LookAhead [OB97].

You configure the maximum cycle load of the MC?LookAhead [OB97] in the properties of the organization block under "General > Cycle load > Maximum cycle load". You can set values from 1% to 40% (default setting 20%) for the maximum cycle load.

Select the cycle load of the MC?LookAhead [OB97] in such a way that the CPU can process all technology objects for Motion Control in one application cycle.

Process response

If the application cycle is not observed, overflows occur. Note the following response to overflows:

The CPU tolerates a maximum of three consecutive overflows of MC?Interpolator [OB92].

The execution of an MC?Interpolator [OB92] may only be interrupted by an MC?Servo [OB91] call.

If more overflows or interruptions occur, the CPU switches to STOP mode.

You can find more information on the process response in the section "Operational Sequence and Timeouts".


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• 6ES7515-2TM01-0AB0

  適用于具有中等/較高要求的應用的 CPU，用于 S7-1500 控制器產品系列中的程序/數據存儲具有中/高處理速度，適用于二進制和浮點數運算在具有集中式和分布式 I/O 的生產線上作為集中式 PLC 使用PROFINET IO IRT 接口，帶 2 端換機PROFINET I/O 控制器，用于在 PROFINET 上運行分布式 I/OPROFINET 智能設備用于連接 CPU 以作為 SIMATI

• “常規”選項卡 -（TIA Portal 項目）

  “另存為新條目”對話框中的“常規”選項卡 -（TIA Portal 項目）“另存為新條目”對話框中“常規”選項卡的結構在“常規”(General) 選項卡的視圖中，包括以下字段和按鈕：字段說明名稱 (Name)：名稱輸入字段，該名稱用于將 TIA Portal 項目另存為 Teamcenter 中的新條目。系統默認顯示所選 TIA Portal 項目的名稱。條目類型 (Item type)：TIA

• PLC data types (UDT)

  PLC data types (UDT)使用的 UDT以下 PLC 數據類型 (UDT) 用于塊庫：TransmitBlockCPU 與 TIM 之間的 UDT 數據傳送使用“Dat256D_S / Dat256D_R”典型值時，將 UDT 復制到相應 CPU 的“PLC 數據類型”(PLC data types) 目錄中。典型值不會自動引用 UDT。UDT *進行任何參數分配。

• 有關移植的基本知識 (WinCC flexible)

  有關移植的基本知識 (WinCC flexible)簡介移植期間，WinCC flexible 項目中的項目數據會轉換為 WinCC 中的新數據格式。系統不會通過對數據進行評估來確定它們是否與待移植項目中的數據一致。編譯期間，如果源項目發出錯誤或警告，移植過程中并不會對其進行修正。這表明在移植之前，應成功編譯項目而不出現任何錯誤。請注意移植過程中的項目范圍。WinCC 的各項功能也可以移植。有關較