西門子V90電機1FL6044-1AF61-0LB1 西門子 代理商

時間：2020-04-04作者：上海西熙工控自動化有限公司瀏覽：64

功能
Feature
Comment
Connection and application macros
Sets groups of parameters to simplify commissioning
?Connection macros for connections
?Application macros for applications
Keep Running Mode
Single-parameter setting for a mode which keeps the motor going – enables
?Vdc_max controller
?Kinetic buffering
?Restart after fault
?Flying start.
?Disables alarms etc.
ECO mode
Economy mode – searches for most efficient rated point
Hibernation mode
Intelligent economy mode in idle state
PID controller
Integrated PID controller with auto-tuning function
Kinetic buffering (Vdc_min controller)
Retention of minimal DC voltage through regenerative energy for continued operation
Vdc_max controller
Automatic change of ramp down time/braking time
Imax controller
Automatic change of ramp up time to avoid overcurrent
Automatic restart
Automatic restart of drive once the power has been restored following a power failure. All faults are acknowledged automatically and the drive is switched on again
Flying restart
Allows the converter to be switched to a rotating motor
Energy consumption monitoring
Displays a simple estimate of energy or cost saved against use of a line-connected motor
50/60 Hz adaptation
Easy selection of operation with 50 Hz (Europe, Asia) / 60 Hz (USA)
V/f and V2/f
V/f: perfectly suitable for almost any application in which the speed of asynchronous (induction) motors is to be changed
V2/f: suited to loads with quadratic load curves, e.g. turbo machines such as pumps and fans
FCC
Maintains motor flux current for improved efficiency
Programmable V/f coordinates
Freely adjusts the V/f characteristics, e.g. torque behavior of the synchronous motor
JOG
Moves the motor to test the direction or moves the load to specific position. When the BOP switches to JOG mode, pressing the start button of the BOP will run the motor up to the JOG frequency.
Releasing the start button stops the motor
DC braking
Stops the motor which runs at constant speed and only comes to a standstill in longer time intervals, e.g. centrifuges, saws, grinding machines and conveyor belts
Mechanical holding brake control
The motor holding brake prevents the motor from undesirable turning when the converter is switched off. The converter has an internal logic to control an external motor holding brake
USS
Universal Serial Interface Protocol
Modbus RTU
Modbus RTU communication available via the RS485 link
Super torque mode
Big torque boost for starting high-inertia applications
Hammer start mode
A number of torque pulses at start-up to start difficult or "stuck" loads
Blockage clearing mode
Multiple-reverse function to clear blocked pumps
Simple parameter-based menu on internal or external BOPs
Easy selection for displaying values, editing parameters, converter setup
Simple text menu for setup
The parameter number will be shown as short text in the 7-segment LED display
Motor frequency display scaling
User settable display scaling for special applications i.e. rather than Hz, it shows application-specific values like "gallons per minute", "potatoes per hour", etc.
Customization of parameter defaults
Customers or OEMs can set their own special "permanent" defaults which can only be deleted in special mode
Converter status in case of a fault
Record the fault with running data

總體介紹
1LE0001 高效系列電動機是鑄鐵機殼通用型全封閉自扇冷卻式三相異步電動機，其防護等級為 IP55，1LE0001 系列電動機設計生產符合 ISO、IEC、GB 等相關標準的要求。采用 1LE0001 系列電動
機，客戶可以節能達 10% 之多！
1LE0001 系列電動機適用于連續工作制（S1）、恒轉速或一定速度范圍內的變頻調速應用。
西門子 1LE0001 系列電動機技術特性
■ 機座和接線盒材料：灰鑄鐵；
■ 標準顏色：石頭灰（RAL 7030）；
■ 額定功率：0.55kW~315kW (50Hz)
■ 0.75kW及以上的 2、4、6 較電動機達到 GB18613-2012 標準能效等級 3 級，且 能滿足 IEC 60034-30 標準中的 IE2 效率等級；
■ 優化的緊湊型結構；
■ 標準安裝結構類型（符合 IEC 60034-7 標準規定）：IM B3、IM B5、IM B35 等；
■ 所有的電動機設計防護等級為 IP55（IEC 60034-5）；
■ FS 1) 280 ~ 355 標配再潤滑裝置，F(xiàn)S 1) 100 ~ 250 的作為選項；
■ 對于 FS 100 ~ 355 范圍電動機，可選擇增強懸臂力設計；
■ 電動機可選 PTC 或 PT100 熱敏電阻或 KTY84-130 進行繞組保護；
■ 接線盒標準位置處于機座*，進線孔處于 右側（從驅動端看），選項中接線盒位置和進線方向可變化；
■ 絕緣系統按 155（F）溫度等級設計，在額定輸出和直接供電時按 130（B）溫度等級使用；
■ 電動機標準冷卻方式為自扇冷卻（IEC 60034-6 規定的 IC 411），可提供獨立驅動風扇強制冷卻；
■ FS 80 ~ 90 電動機沒有吊環；FS 100 ~ 315 電動機都有 2 個吊環，F(xiàn)S 355 電動機有 1 個吊環用于運輸。
1) FS，機座的英文（Frame Size）縮寫。
運行環境
■ 防護等級 IP55（IEC 60034-5）；
■ 高度不**過海拔 1000 m（IEC 60034-1）；
■ 允許的環境溫度在 -20 oC ~ 40 oC（IEC 60034-1）；
■ 所允許的相對濕度：
? -20 oC ≤ T ≤ 20 oC：100 %
? 20 oC < T ≤ 30 oC：95 %
? 30 oC < T ≤ 40 oC：55 %
對于較高的環境溫度、以及（或者）**海拔 1000 m 的地點，電動機的額定功率換算系數為 k HT 。所允許的功率值（P adm ）：
P adm = P rated ? k HT
應用
變頻應用
1LE0001 電動機適于變轉速、恒轉速的各種應用，如風機、泵、壓縮機、紡織機械等。
當變頻器驅動電動機時，電磁干擾的程度大小取決于變頻器的類型（種類，IGBT 數量，干擾控制措施及制造商）、布線、距離以及應用需求。在設計和應用階段必須參考變頻器制造商關于電磁兼容性的安裝指導。
當 1LE0001 電動機變頻應用（變頻器供電），且輸出額定功率時，電動機的使用溫度等級為 155（F）。為了避免雜散電流對電動機軸承的損壞，推薦 FS250 ~ 355 電動機使用絕緣軸承。請向西門子咨詢關于絕緣軸承的詳細信息。
變頻器驅動運行
1LE0001 電動機的標準絕緣系統設計要求，能夠保證其在變頻器供電電壓不**過 460 V 時正常運行。
1LE0001 電動機帶有特定的負載時能夠使用變頻器驅動，其特定的負載扭矩如以下圖表所示：
當負載轉矩在允許的轉矩范圍內時，電動機能夠自扇冷卻；當負載轉矩**過所允許的轉矩時，電動機需要強迫冷卻。
在電動機運行速度**過額定轉速時，噪聲和振動值將增加，并且軸承的壽命將縮短。需要注意再潤滑周期和潤滑脂的壽命。
變頻運行時當頻率**過 60 Hz 時，必需按照特定的限值進行動平衡。
電壓（峰值和梯度值）承受值
繞組絕緣的電介質應力決定于：
?電壓峰值，啟動時間以及變頻器產生的脈沖頻率；
?變頻器與電動機連接電纜的特性和長度；
?繞組結構和其他系統參數，尤其是絕緣系統中不同繞組的對地電壓（代表了絕緣系統的電介質應力）。

Easy to use
?Parameter settings can be easily transferred from one unit to another using the battery-operated parameter loader.- Less technical support required
- Short commissioning time
- The product is delivered to the customer already preset
?Integrated connection and application macros
To simplify I/O configuration and make the appropriate settings- Shorter commissioning time
- Integrated and optimized application setting
- Simple connection and application macros can be selected instead of configuring long, complicated parameter lists
- Errors caused by wrong parameter settings can be avoided
?Keep Running Mode allows uninterrupted operation
This function provides higher productivity in production by automatic adaptation in the case of unstable line supplies- Stable operation under difficult line supply conditions
- Higher productivity through prevention of interruptions to the production line
- Adaptation to application-relevant reactions through flexible definition in case of faults/alarms
?Wide voltage range, advanced cooling design and coated PCBs increase robustness of the drive in difficult environments- Operation possible when the line supply voltage fluctuates
- Reliable operation at line voltages:
200 V ... 240 V 1 AC (-15 %/+10 %) 1)
380 V ... 480 V 3 AC (-15 %/+10 %)

應用
Typical applications
Pumping, ventilating, compressing
Advantages
?Centrifugal pumps
?Radial/axial fans
?Compressors
?High availability through automatic restart and flying restart after power failures
?Broken belt detection by monitoring the load torque
?Pump protection against cavitation
?Hammer start and blockage clearing modes for clogged pumps
?PID controller for process values (e.g. temperature, pressure, level, flow)
?PID auto tuning to optimize controller parameters
?Hibernation mode stops the motor when demand is low
?Motor staging extends the flow range by adding two more fixed-speed drives (cascade)
?Frost and condensation protection prevents moisture in motors under extreme environmental conditions
?With optional SINAMICS V20 I/O Extension Module for 400 V converters: Multi-pump control 1), with which up to four pumps can be controlled with a frequency converter and applications that require additional digital inputs and digital outputs (e.g. in water supply systems for buildings)
Moving
Advantages
?Conveyor belts
?Roller conveyors
?Chain conveyors
?Moving walkways
?Bucket conveyors
?Soft, jerk-free acceleration reduces the stress on the gear units, bearings, drums and rollers
?Super torque start for conveyor belts with high breakaway torque
?Dynamic behavior by using braking resistor or DC braking
?Direct control of mechanical holding brake
?Broken belt detection by monitoring the load torque
?Precise stopping with Quick Stop (switch-off positioning) independently of the control cycle
Processing
Advantages
?Single drives in the processing industry such as mills, mixers, kneaders, crushers, agitators, centrifuges
?Single drives in commercial applications such as ovens, mixers, industrial washing machines
?Main drives in machines with mechanically coupled axes such as spinning machines, braiding machines for textiles, ropes and wires
?Frost and condensation protection prevents moisture in motors under extreme environmental conditions
?Higher productivity with uninterrupted production due to Keep Running Mode
?Exchange of regenerative energy via the DC link
?Super torque start for machines with a high breakaway torque


-/gbadicf/-

上海西熙工控自動化有限公司專注于西門子PLC模塊代理商,西門子電纜代理商等

• 詞條

  詞條說明

• 西門子控制面板6AV2123-2GA03-0AX0 西門子 新聞資訊

  SIMATIC HMI 按鍵式面板具有大號機械按鍵和多種顏色的照明燈（日光下可讀），十分易于操作接線和安裝時間節省 60% 以上（即插即用）與常規鍵盤式操作員面板相比，材料成本節約 30% 以上2 個集成 PROFINET 端口（含交換機），用于設置總線型和環型拓?fù)淇勺杂山M態的數字量 I/O 可在后面連接其他鍵控開關、指示燈等可連接 KP8F 和 KP32F 的故障安全急停按鈕或其它故障安全信號(

• 西門子6SL3 244-0BB00-1BA1 西門子 資訊

  外形尺寸從 FSA ~ FSF 的功率模塊 PM230 具備高達 IP55/UL Type12 的防護等級，且提供針對 C2 類安裝的集成 A 級進線濾波器的規格，以及針對 C1 類安裝的集成 B 級進線濾波器的規格。PM230，IP20：? 外形尺寸 FSA ~ FSF 尺寸的功率模塊 PM 230 可以提供 IP20/ULOpen Type 的防護等級，并提供內置 A 級濾波器或不帶內置濾波器

• 西門子WINCC軟件6AV6381-2BN07-0AV0 西門子 購買指南

  WinCC 語言版本SIMATIC WinCC 專門為亞洲市場提供有簡體中文，繁體中文，韓文以及日文的語言支持。這些 WinCC 版本專門用于機器制造商，工廠建造者以及為中國，閩臺，韓國和日本供貨的出口人員。WinCC ASIA 包括所有的 WinCC 系列功能，并提供有使用各國語言和英語組態的用戶接口。在線幫助提供了簡體中文、繁體中文、韓文、日文和英文的各種版本。運行時要求中文，韓文，日文或多語

• 西門子V7.5運行版6AV6381-2BE07-5AV0 西門子 資訊

  HMI 系統和上位系統之間的開放式通信?OPC 服務器/客戶端 將可視化系統用作數據服務器（OPC 服務器），用于上層自動化組件，如控制系統或辦公領域中的系統- OPC-DA 服務器：變量，如過程值 - OPC-HDA 服務器：記錄的過程值 - OPC-A&E 服務器：報警 - OPC-XML-DA 服務器：變量，如過程值- OPC-XML-DA 服務器：變量，如過程值- OPC-UA-DA 客戶