Application of open type Hall current sensor in power distribution system modification in a Russian factory

時間：2021-06-23作者：安科瑞電子商務（上海）有限公司瀏覽：120

朱鹍
安科瑞電氣股份有限公司  上海嘉定



Abstract: According to the principle, characteristics and installation mode of the open-type Hall current sensor, the application of the open-type Hall current sensor in the transformation and distribution system of the factory is analyzed, so as to provide a solution for users to realize the intelligent distribution of DC system quickly.

 

Key words: open type Hall current sensor  DC distribution system  working principle  application

 

0 Overview
  DC distribution system is usually composed of high frequency switching power supply and battery, which is used to provide reliable DC power supply for control, **, relay protection and automatic devices, accident lighting and so on in DC system. It has high requirements for the reliability, stability and quality of power supply. Therefore, in the Russian DC system, we matched the DC Hall distribution meter used. During the transformation of DC system, there is no power outage, and the engineering transformation is difficult, and the traditional closed Hall current sensor or shunt can not solve the problem. Therefore, the open Hall current sensor can be used to solve the DC current measurement problem in the transformation project, so as to ensure the safe operation of the transformation process without power outage.

 

1 Product Design   
1.1Structural features    
  Open-mouth Hall current sensor is developed on the basis of traditional closed-mouth Hall current sensor. It has novel structure and beautiful appearance. The whole is composed of shell, iron core, sampling circuit board and fixed resin. The shell material is made of PC/ABS alloy, which has the characteristics of high temperature resistance, high mechanical strength and environmental protection. The core is made of oriented cold bonded silicon steel sheet, which has the characteristics of stable performance, high mechanical strength and extremely high magnetic conductivity. Green pluggable terminal is used for circuit board and external wiring, which is convenient and reliable for on-site wiring. The specific structure is shown in Figure 1 and 2. The appearance of the product adopts split design. Figure 1 is a round pass, which is suitable for passing through the DC system when the primary bus is a cable. , Fig. 2 square pass, suitable for the DC system when the primary bus is copper bar. According to the measurement range of primary current and perforation requirements, the corresponding product type can be selected. This series of sensors can measure the current range of 20A ~ 20000A, the main shape of the phi 20, 40, 60, 64*16, 85*27, 104*36, 140*50 and other specifications, as shown in Figure 3, suitable for different applications.
 


              
                   Fig. 1 circular pass pattern                                            Fig. 2 Square pass pattern                           


                   
       Figure 3 AHKC series open type Hall current sensor

 

1.2 Working principle
  Hall current sensor based on hall effect, electromagnetic induction principle, design of a sensor, according to the principle can be divided into the open loop mode (straight) and closed loop mode (magnetic balance type), open hall current sensor is in a traditional open loop (straight) is improved on the basis of hall sensor, is different from traditional single core, single chip design hall, In order to design a split structure, the iron core is separated and installed symmetrically. The hardware adopts parallel complementary differential input of double Hall chips. The principle of open-type Hall sensor is shown in Figure 4:

 

  Fig. 4 Schematic diagram of open Hall sensor


  When the primary side current IP flows through a long wire, will produce a magnetic field around the wire, the size of the magnetic field and is proportional to the current through the wire, the magnetic field gathered in the circular, through two hall element in the circular air gap measurement, two hall element marks instead placed in the same field, the output ** with complementary characteristics of output voltage by differential amplifier output, Not only can suppress the common mode interference, but also the influence of temperature drift, the output voltage VS accurately reflect the original side current IP. The general rated output is calibrated as DC±5V or DC4-20mA.

 

1.3 Product installation
  Take square-hole products as an example, as shown in Figure 5, open the mounting screw of the open-type Hall current sensor, and remove the lower body of the sensor; The upper body of the open type Hall current sensor is loaded into the primary bus of the distribution system, and the lower body of the sensor is closed. The mounting screws and gaskets of the sensor pass through the fixing holes of the upper and lower bodies, and the upper and lower bodies of the sensor are fixed together. If on-site power off installation is possible, two corresponding threaded holes can be opened on the bronze plate according to the sensor spacing requirements, and the sensor is fixed on the threaded hole of the bus bar through the rear mounting fixing hole to complete the installation of the sensor; If the site requires continuous electric installation, the supporting rubber pad can be embedded between the shell and the bronze plate to ensure that the sensor can work reliably under vibration conditions. The whole installation process is relatively quick and simple. 

 

 
Fig. 5 Product installation diagram

 

1.4 Advantages of open type Hall sensor
  Compared with the traditional DC current measurement method generally adopted by shunt or transformer, the open-type Hall sensor has the following advantages:
1) High insulation strength of primary side and secondary side, up to AC 12KV isolation;
2) No insertion loss;
3) Good dynamic performance: the response time is less than 20uS and the tracking speed Di /dt is higher than 20A/ uS
4) There is no need to disassemble the original side cable or bus during installation. It is especially suitable for the transformation and construction of equipment that is not allowed to lose power.

 

2. Product application
   Open-end Hall current sensor is mainly used in the transformation of DC distribution system in factories, such as DC power system transformation in power plants, DC system transformation in substations, communication room transformation, railway locomotive transformation and other projects. It can convert the central edge DC current ** of the system into standard DC± 5V or 4-20mA output. It plays the role of monitoring and electrical isolation, and can be used with multi-loop monitoring instruments or other electrical measuring instruments.   

 

3.Conclusion
  Open-end Hall current sensor plays an important role in the application of DC system because of its simple structure, convenient installation, reliable operation and other good applicability, especially in the renovation project.

 

Bibliography
1.Solutions For Enterprise Micro-grid System 2020.04

作者簡介：
朱鹍，女，就職于安科瑞電氣股份有限公司，主要研究方向?yàn)槠髽I(yè)能源管控



安科瑞電子商務（上海）有限公司專注于變電所運維云平臺,安全用電管理云平臺,環保用電監管云平臺等, 歡迎致電 15000353138

• 詞條

  詞條說明

• 淺談電能管理系統在混合動力港拖輪中的應用

  朱鹍安科瑞電氣股份有限公司? 上海嘉定? 201801摘要：隨著現代造船技術的發展，船舶對電能管理系統的可靠性和經濟性要求越來越高，因此船舶電站的控制、監視和管理的重要性越來越**。根據油 電混合動力港作拖輪 電能管理系統的特 點，對該船電力系統的組成和功能要求進行分析，在此基礎上，對該船電能管理系統進行了詳細設計。本船以西門子s71200型號PLC作為**控制器，并對柴油發電

• 高校數據維護與管理

  摘 要：隨著信息技術的不斷進步和信息系統的應用擴大，大規模的數據也在不斷增長。建立大數據以加速數據資源的共享和應用已成為一項戰略。在高等教育領域，大學是進行特殊教育的機構，大學信息化也進入了大數據時代。本文分析了大學所面臨的數據的維護與管理問題，并對此提供了安科瑞的電力監控解決方案。??關鍵詞：高校；大學；數據?1引言? ? ?隨著信息技

• 關于用電檢查對企業安全用電的重要性

  朱鹍（安科瑞電氣股份有限公司 ?上海嘉定 ?201801）?摘要：隨著社會經濟的發展，各行業用電量急劇增加，促進了電力市場的長足發展。作為電力企業的基礎工作，用電檢查是服務于用電企業的重要部分，且對企業安全用電具有重要意義。在用電檢查過程中，電力企業為用電企業提供優質的用電檢查服務，不僅能樹立良好的形象，增強電力市場競爭力，還能為企業安全用電提供有力**。本文以用電檢

• 阿里巴巴西溪園區四期電力監控系統 的設計與應用

  朱鹍安科瑞電氣股份有限公司，上海 嘉定 201801；摘要：介紹阿里巴巴西溪園區四期電力監控系統，采用綜合保護裝置、多功能儀表、變壓器溫控儀、直流屏，采集配電現場的各種電參量和狀態信號。系統采用現場就地組網的方式，組網后通過現場總線通訊并遠傳至后臺，通過安科瑞電力監控系統實現變電所變配電回路用電的實時監控和管理。?關鍵詞：阿里巴巴西溪園區四期電力監控系統；35KV變配電所；綜合保護裝置；