儀表SIL功能安全評估檢測認證流程

時間：2020-02-27作者：江蘇中正檢測股份有限公司瀏覽：83

認證模式：1.填寫申請表，提供相關檢測報告，直接發證
                 2.送樣檢測+審廠
Work Packages 工作階段說明
Position 1 : Concept phase 
1 ：概念階段
The concept phase consists of the following activities: 
本階段包括下列事項：
? Inspection and review of the Safety Plan and Verification and Validation Plan (V&V Plan) for
compliance with the requirements of IEC 61508 and IEC 61513
依據 IEC 61508 及 IEC61513的要求， 針對安全計劃和 V&V 計劃進行檢驗和審核
? Inspection and review of the functional and safety related specification of the product
針對產品的功能和安全相關的需求規范進行檢驗和審核
? Assessment of the planned measures to avoid faults (QM) during the various phases of the
product life cycle, especially during the development process
對計劃的措施進行評估， 以避免在產品生命周期各階段， 尤其是開發階段中可能出現的失效
? Inspection and assessment of the planned measures for the detection and control of faults
(diagnostic measures)
對計劃的措施進行檢查和評估， 以發現和控制失效（診斷措施）
? Inspection of an FMEA on structural level
基千架構進行 FMEA 檢查
? Definition, agreement of requirements for Electrical Safety
電氣安全要求的定義和協定
? Definition, agreement of requirements for environmental test, incl. EMC
環境測試包括 EMC 的測試要求定義
? Inspection and assessment of the planned documentation system (design documentation and
documentation of the verification activities)
針對計劃的文檔系統進行檢查和評估（設計文檔和驗證文檔）
? Preparation of a test plan for the main inspection
為主檢階段定制測試計劃
? Report upon the concept inspection
基千概念檢查出具報告
（頁碼／Page: 1/2) 
Position 2: Main approval 
2：主檢階段 The main approval phase consists mainly of the following steps: 
主要認可階段主要包含以下步驟：
? Test of all safety related functions, analysis of the functionality
針對安全相關的所有功能進行測試， 分析其功能性
? Test and verification of the measures for the detection and control of faults in HW and SW C If
included software)
測試和驗證用千檢測和控制軟件及硬件失效的措施（如果有軟件）
? Review of the FMEA for subsystems
針對子系統進行 FMEA 評審
? Inspection of the SW-verification tests (module, integration and system tests) performed by the
manufacturer C If included software)
針對制造商進行的軟件驗證測試進行檢查（測試包括模塊、 集成和系統測試）－如有軟件
? Assessment of the applied measures for the avoidance of faults (QM) during the product life
cycle, especially during the development process (check lists)
評估在產品生命周期中應用避免失效的措施（質暈管理體系）， 特別是研發過程中可能出現的失效
（檢查表）
? Inspection and assessment of the product documentation compiled during the various phases of
the development cycle
針對產品研發周期各階段的產品文檔進行檢查和評估
? Test of the electrical safety/ equipment
電氣安全／設備的測試
? Inspection and review of the reports on the environmental tests, incl. EMC
檢查、 審核環境測試報告（包含 EMC 測試）
? Inspection and review of the calculations of the data for safety related reliab仆ity performed by the
manufacturer
檢驗、 審核由制造商提供的安全相關可靠性數據的計算
? Inspection and review of the documentation for the user (Installation and operating instructions,
manual, etc.)
檢驗、 審核用戶使用文件， 包括安裝和操作規程，手冊，等基于檢查出具報告
? Factory inspection
工廠審核
Position 3: Certification 
3: 認證階段
The certification will be made by the certification authority based on the test report. 
由認證機構 基于檢測報告進行發證。


江蘇中正檢測股份有限公司專注于UIAA認證,CE認證,FIBA等

• 詞條

  詞條說明

• 儀表SIL功能安全評估檢測認證流程

  認證模式：1.填寫申請表，提供相關檢測報告，直接發證 2.送樣檢測+審廠 Work Packages 工作階段說明 Position 1 : Concept phase 1 ：概念階段 The concept phase consists of the following activities: 本階段包括下列事項： ? Inspection and review of the Safety Pl