Configuring the digital inputs and digital inputs/outputs (X122/X132)

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：127

Configuring the digital inputs and digital inputs/outputs (X122/X132)



The digital inputs and digital inputs/outputs (X122/X132) are mainly assigned to SINAMICS Integrated. Through configuration (frames 39x), you can, however, also use the digital inputs and digital inputs/outputs (X122/X132) for the CPU. The following applies:

A digital output is always only available exclusively to SINAMICS Integrated or to the CPU.

If you use a digital input for the CPU, you can also interconnect the digital input at the drive end.

You can configure the digital inputs and digital inputs/outputs (X122/X132) channel by channel. To do so, go to the function view in the project tree under "Automatic speed control" > "Parameter assignment" and set the configuration under "Inputs/outputs".

Bidirectional inputs/outputs are configured in the following configuration mask.


圖片: Bidirectional inputs/outputs

You can assign the SINAMICS digital inputs and digital inputs/outputs (X122/X132) using frame 39x of the PU. The status information of the digital inputs and digital outputs is then transferred at the PROFIdrive PZD sampling rate (p2048). The inputs/outputs are also sampled in the configured sampling time for the digital inputs and digital inputs/outputs (p0799). The application of the output values and return of the input values are therefore subject to dead times and jitter.


圖片: Configuration of frame 393 for automatic speed control

You can find further information on the various different frame types in .

提示 Interface X142 If you have particularly strict requirements for the digital input/outputs, use the digital input/outputs at interface X142. The digital inputs/outputs can be operated in isochronous mode and allow very short response times.


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• 代理服務器

  代理服務器在此頁面中，可組態不同組件（例如 SINEMA RC）使用的代理服務器。說明代理名稱 (Proxy Name)輸入代理服務器的名稱。該表格包括以下列：名稱 (Name)顯示代理服務器的名稱。地址 (Address)輸入代理服務器的 IPv4 地址。類型 (Type)*代理服務器的類型。-?HTTP：**通過 HTTP 進行訪問的代理服務器。-?SOCKS：通用代理服

• Win10中安裝WinCC V7.5

  通常 WinCC V 7.5 的產品包裝中包含三張光盤。分別是 WinCC V7.5 、SIMATIC NET V 15和 additional Content。其中，WinCC V7.5是基本的安裝包，SIMATIC NET V15 提供了通訊所必須的驅動程序，Additional Content 中提供了SQL SERVER 的管理工具。安裝時需要注意以下事項：1.安裝環境需要滿足軟件的兼容性

• MAP庫移植

  MAP庫移植S7-200 MAP 庫移植至 S7-200 SMART 運動控制，移植時需要在 S7-200 SMART 中通過運動控制向?qū)Ь幊?。測量系統移植1、如果 MAP 庫使用相對脈沖，S7-200 SMART 運動控制向?qū)У臏y(cè)量系統選擇相對脈沖，如圖1：圖1. 選擇測量系統2、S7-200 SMART 運動控制向?qū)У姆较蚩刂聘鶕?jù)實際情況可以選擇“單相（1個輸出）”或者“單相（2個輸出）”，如

• 組態安全功能*墻綜述

  綜述可在此頁面激活*墻。提示請記住，如果禁用*墻，內部網絡將不會受到保護。說明該頁面包含以下內容：激活*墻 (Activate Firewall)啟用后，*墻有效。TCP 空閑**時 [秒] (TCP Idle Timeout [s])輸入所需的時間（單位：秒）。如果未發生任何數據交換，則 TCP 連接將會在該時間結束后自動終止。值范圍是 1 到 21474836。默認設置：86400 秒U(xiǎn)